Local Storage seems to be disabled in your browser.
For the best experience on our site, be sure to turn on Local Storage in your browser.
Lora6102AES - 1W - AES Encrypted - LORA - High Power Wireless Transceiver - Data Transmission Module
LoRa6102AES is an industrial-class wireless transceiver data transmission module with aluminum housing, based on SX1276/1278 chips from Semtech. This module adopts LoRa technology to achieve high effective sensitivity and superior anti-interference. For better security, the module uses AES128 encryption. LoRa6102AES has 1W output power and TTL/RS232/RS485 interface available. It is widely applied in meter reading, remote industrial control, etc
Feature and application:
Feature:
-
Transmission distance in open area up to 8000 meters @ 91bps
-
433/470 (1W) MHz 868/915 (500Mw) MHz
-
40 channels
-
LoRa modulation
-
Interface: TTL/RS232/RS485
-
Sensitivity: -139 dBm
-
Max output power: 1W/500mW(+30dBm/+27dBm)
-
Working voltage: 3.3 ~ 6.5 V
-
Working temperature: -40 ~ +85 °C
Application:
-
Remote control telemetry
-
Remote meter reading
-
Security system
-
Industrial data acquisition
-
Home automation
-
Wireless data communication
-
Access system
-
Robot control
Specification:
Electrical Characteristics:
Functional description:
Block diagram:
Operation
1) Power on Reset
Standard supply voltage of 5V (ordinary lithium battery of 4.2V is also applicable),After powered on reset, the TX LED (Red) and RX LED (Blue) will blink 3 times,(If no lights, the module may damaged), The total reset time is around 2s, as below:
2) Working Mode
The CS and SET Pin is internally pulled up. Pull CS pin high or leave it open will make Lora6102AES enter into working mode.
In working mode, Lora6102AES stay in receiving mode and wait for the series signal and RF signal. Lora6102AES can connect with any device which is a standard TTL interface.
-
When the series signal comes, Lora6102AES will check the input series signal if there is any error, and then transmit the received data out via RF automatically if no errors found.
-
When RF signal comes, Lora6102AES will check the input RF signals if there is any error, and then transmit the received data out via series port automatically if no errors found.
-
When one packet is transmitted successfully, the Red LED will blink once.
-
When one packet is received and verified with no problem, the Blue LED will blink once.
The easiest way to test the module is by using a computer(PC software)
Pin and dimension:
pin definition:
Mechanical dimension:
FAQ:
Why module cannot communicate properly?
a) Check if the band, channel, rate, NET ID has set to the same;
b) Check if there is a power connection error;
c) Check if the module is enabled (CS high);
d) Check if the antenna connection is not correct;
e) Check if the module is damaged.
Why transmission distance is not as far as it should be?
a) Power supply ripple is too large;
b) The antenna types do not match, or not properly installed;
c) The surrounding environment is harsh, strong interference sources;
d) Surrounding co-channel interference;
Why receiving data incorrect?
a) Improper parameter settings;
b) The module data interface is bad.
Subtitle | N/A |
---|---|
UPC/EAN | 4604046162232 |
Count | N/A |
M.R.P | ₹9,378.00 |
Brand Name | CentIoT |
Model | Lora6102AES |
Whoesale | Available |
Supply Voltage | N/A |
Dimension | 13X12X10 cm |
Working voltage range | 3.3 ~ 6.5 V |
Data transfer rate | N/A |
Receiving sensitivity | -139 dBm |
Maximum output power | 1W/500mW,(+30dBm/+27dBm) |
Sleep current | <40 μA |
Receiving current | <20mA |
Operating Temperature Range | -40 ~ +85 °C |
Data Rate | @LoRaTM 656 bps |
Operating Temperature | N/A |
Frequency | 433/470 (1W) MHz 868/915 (500Mw) MHz |