SV612

G-NiceRF| SV612 100mw Industrial anti-interference | Si4432 Wireless RF | data transceiver module

G-NiceRF UART transmitter and receiver RF module|433MHz 470MHz|SI4432|SV6202-Mesh 2W mesh network RF module with aluminum housing

SV-MESH series are ultra long distance MESH network data transceiver modules, which adopts the high-performance Silicon Labs Chips. They have NODE and ROUTER working modes, can be as repeaters automatically. It is easy to build a network without blind area or distance limitation. To avoid interference, SV-MESH provides 40 frequency channels and configurable Net ID. SV-MESH is flexible but easy to use, it comes with many parameters, such as frequency, data rate, output power, Net ID, Node ID. Users can configure the parameters through a PC or customer’s own device.

₹3,465.00
Out of stock
SKU
SV6200-MESH

Features:

  • Repeat automatically

  • GFSK modulation

  • 40 channels

  • 4 bytes Net ID

  • Default 2 bytes Node ID

  • Serial parameters configurable

  • RSSI

  • TTL/RS232/RS485/USB for option

  • Max output power: 2W for option

  • Frequency band: 433/470/868/915Mhz for option

  • Sensitivity up to -121 dBm

  • Working temperature: -40 ~ +85 °C

Applications:

  • Robot control

  • Remote control telemetry

  • Industrial data acquisition

  • Wireless data communication

  • Access control system

  • Remote meter reading

  • Security system

  • Home automation

Specification:

Electrical characteristics:

Electrical Characteristics

Functional description:

Note:

1)When worked with TTL or RS232 interface, the serial port of modules should cross match with the serial port of customer’s device(TXD(A+) to RXD, RXD(B-) to TXD).

2)For RS485 interface, the serial port of module match the serial port of customer’s device(A to A, B to B)

3)The ground pin of the module and device should be connected together

Typical connection as below



Application circuit

Operation

1. Power on Reset

After powered on reset, the TX LED (Red) and RX LED (Blue) will blink 3 times, The total reset time is around 2s, as below:

2.Working mode

The CS and SET Pin is internally pulled up. Pull CS pin high or leave it open will make modules enter into working mode, the serial and RF are both in receiving mode then.

In NODE working mode, SV6200-MESH module stays in receiving mode and wait for the series signal and RF signal. SV6200-MESH module can connect with any device which is a standard TTL interface.

  • When the series signal comes, SV6200-MESH module will check the input series signal if there is any error, and then transmit the received data out via RF automatically if no errors found.

  • When the RF signal comes, SV6200-MESH module will check the input RF signals if there is any error, and then transmit the received data out via series port automatically if no errors found.

  • When one packet is transmitted successfully, the Red LED will blink once.

  • When one packet is received and verified with no problem, the Blue LED will blink once.

The easiest way to test the module is by using computer(PC software)

3.Router mode

When set as ROUTER, in working mode, SV6200-MESH module can repeat the RF signal in the same network automatically to extend the distance.

Normally, Router module is connected with the external power supply to keep a long time in receiving mode and repeat the signal to extend the range

To ensure the stability and correctness of communication, please notice the following tips:

1) To ensure the normal working of ROUTER, the node should send the data with minimal time interval between adjacent packets. The time interval is different from the data length, RF data rate and baud rate.

When the RF data rate is the same as the baud rate, and the data length is 56bytes, the minimal time interval as below:


pin and dimension:

Pin definition:

pin definition

Mechanical Dimension:

Mechanical Dimension

FAQ:

A. Why module cannot communicate properly?
1) Check if there is a power connection error;
2) Check if the module is enabled (CS / SET both high);
3) Check if the band, channel, rate, NET ID has set to the same;
4) Check if the module is damaged(light is on?)
B. Why transmission distance is not as far as it should be?
1) Power supply ripple is too large;
2) The antenna types do not match, or not properly installed;
3) The surrounding environment is harsh, strong interference sources;
4) Surrounding co-channel interference;
C. Why receiving data incorrect?
1) Check if the interface compatible with the device;
2) Improper parameter settings.
3) The module data interface is bad.
More Information
Subtitle N/A
UPC/EAN 4604046162263
M.R.P ₹6,930.00
Brand Name G-NiceRF
Model N/A
Whoesale Available
Supply Voltage N/A
Dimension 13X8X9 cm
Working voltage range 4.5-6.5V
Data transfer rate N/A
Receiving sensitivity -121 dBm
Maximum output power 2W(+33dBm)
Sleep current N/A
Receiving current N/A
Operating Temperature Range -40 ~ +85 °C
Data Rate 1.2-115.2 kbps
Operating Temperature N/A
Frequency 443/470 MHz
Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account

No Related Posts