Lora6102AES - 1W - AES Encrypted - LORA - High Power Wireless Transceiver - Data Transmission Module

Lora6102AES - 1W - AES Encrypted - LORA - High Power Wireless Transceiver - Data Transmission Module

RF2541-PL2 BLE4.0 UART Interface-CC2541 Bluetooth Module

RF2541-PL2 BLE4.0 UART Interface-CC2541 Bluetooth Module

Lora6103AES - USB Interface - 1W - AES Encrypted - LORA Wireless Transceiver - Data Transmission Module

LoRa6103AES is an industrial-class wireless transceiver data transmission module with aluminum housing, based on SX1276/1278 chips from Semtech. This module adopts LoRa technology to achieve high effective sensitivity and superior anti-interference. For better security, the module uses AES128 encryption. LoRa6103AES has 1W output power and a USB interface available. It is widely applied in meter reading, remote industrial control, etc

₹5,449.00
In stock
SKU
Lora6103AES

Feature and application:

Feature:

  • Transmission distance in open area up to

  • 8000 meters @ 91bps

  • 433/470 (1W) MHz

  • 868/915 (500Mw) MHz

  • 40 channels

  • Lora modulation

  • USB Interface

  • Sensitivity: -139 dBm

  • Max output power: 1W/500mW,(+30dBm/+27dBm)

  • Working voltage: 4.5 ~5.5 V

  • Working temperature: -40 ~ +85 °C

Application:

  • Remote control telemetry

  • Remote meter reading

  • Security system

  • Industrial data acquisition

  • Home automation

  • Wireless data communication

  • Access system

  • Robot control

Specification:

Electrical Characteristics:

Functional decsription:

Block diagram:

Operation

1) Power on Reset

Standard supply voltage of 5V (ordinary lithium battery of 4.2V is also applicable),After powered on reset, the TX LED (Red) and RX LED (Blue) will blink 3 times,(If no lights, the module may damaged), The total reset time is around 2s, as below:

2) Working Mode

After Power-on reset, Pull SET pin high or leave it open will make Lora6103AES enter into working mode.

In working mode, Lora6103AES stay in receiving mode and wait for the series signal and RF signal. LORA6103AES can connect with any device which is a standard USB interface.

  • When the series signal comes, Lora6103AES will check the input series signal if there is any error, and then transmit the received data out via RF automatically if no errors found.

  • When RF signal comes, Lora6103AES will check the input RF signals if there is any error, and then transmit the received data out via series port automatically if no errors found.

  • When one packet is transmitted successfully, the Red LED will blink once.

  • When one packet is received and verified with no problem, the Blue LED will blink once. The message is encrypted by AES128, the key is configured by PC software.

pin and dimension:

Pin definition:

Mechanical Dimension:

FAQ:

Why module cannot communicate properly?

a) Check if the band, channel, rate, NET ID has set to the same;

b) Check if there is a power connection error;

c) Check if the module is enabled (CS high);

d) Check if the antenna connection is not correct;

e) Check if the module is damaged. 

Why transmission distance is not far as it should be?

a) Power supply ripple is too large;

b) The antenna types do not match, or not properly installed;

c) The surrounding environment is harsh, strong interference sources;

d) Surrounding co-channel interference; 

Why receiving data incorrect?

a) Improper parameter settings;

b) The module data interface is bad

More Information
Subtitle N/A
UPC/EAN 4604046162225
Count N/A
M.R.P ₹10,898.00
Brand Name CentIoT
Model Lora6103AES
Whoesale Available
Supply Voltage N/A
Dimension 11X9X10 cm
Working voltage range 4.5 -5.5 V
Data transfer rate N/A
Receiving sensitivity -139 dBm
Maximum output power 1W/500mW,(+30dBm/+27dBm)
Sleep current <40 μA
Receiving current <20mA
Operating Temperature Range -40 ~ +85 °C
Data Rate @LoRaTM 656 bps
Operating Temperature N/A
Frequency 433/470/868/915 MHz(Customizable)
Write Your Own Review
Only registered users can write reviews. Please Sign in or create an account

No Related Posts